PS skirting, also known as polystyrene skirting, has become a popular choice for homeowners and interior designers alike due to its affordability, ease of installation, and aesthetic appeal. As a supplier of high – quality PS skirting, I’m excited to share with you a comprehensive guide on how to install PS skirting in your space. PS Skirting
Pre – installation Preparations
Before you start installing PS skirting, there are several essential steps you need to take to ensure a smooth and successful process.
Measure Your Space
The first step is to measure the perimeter of the room where you plan to install the skirting. Use a tape measure to accurately measure the length of each wall, noting down any corners, doorways, or windows. Make sure to account for any gaps or overlaps that may occur at intersections. When measuring around doorways and windows, measure the inner edges of the openings, as the skirting will need to fit snugly around these areas.
Gather Materials and Tools
In addition to the PS skirting boards, you will need a few tools and materials for the installation. These include:
- Adhesive: Choose a high – quality adhesive specifically designed for bonding PS skirting to walls. Look for an adhesive that offers strong adhesion and fast drying time.
- Silicone Sealant: This is used to seal the gaps between the skirting and the wall or floor, providing a finished look and preventing dust and debris from accumulating.
- Mitre Saw: A mitre saw is essential for cutting the skirting boards at the correct angles, especially at corners. Make sure the saw is sharp and in good working condition.
- Measuring Tape: Used to take accurate measurements of the walls and skirting boards.
- Pencil: To mark the cutting and installation points on the skirting boards.
- Spirit Level: To ensure that the skirting boards are installed straight and level.
- Utility Knife: For cutting the skirting boards to length and trimming any excess material.
Prepare the Wall
Before installing the skirting, the wall surface must be clean, dry, and free of any dust, dirt, or grease. Use a damp cloth to wipe down the wall, and if necessary, sand the surface to create a smooth and even bonding area. Remove any loose paint or wallpaper from the wall, as this can affect the adhesion of the skirting.
Cutting the Skirting Boards
Once you have measured your space and gathered all the necessary tools and materials, it’s time to cut the skirting boards to size.
Straight Cuts
For straight sections of wall, use a mitre saw to cut the skirting boards to the required length. Place the skirting board on the mitre saw, aligning it with the appropriate measurement on the saw blade guide. Make sure the saw blade is set at a 90 – degree angle for straight cuts. Use a firm grip on the skirting board and slowly lower the saw blade through the material, following the cut line precisely.
Mitre Cuts
At corners, you will need to make mitre cuts to ensure a seamless fit. A mitre cut is a 45 – degree angle cut that allows the skirting boards to meet neatly at the corner. To make a mitre cut, set the mitre saw blade to a 45 – degree angle. Place the skirting board on the saw, aligning it with the appropriate measurement and the 45 – degree angle guide. Make sure the skirting board is held firmly in place, and then carefully lower the saw blade through the material. Repeat this process for the other skirting board that will meet at the corner, making sure to cut the mitre in the opposite direction.
Cutting Around Obstacles
When installing skirting around doorways, windows, or other obstacles, you may need to make custom cuts. Measure the width and height of the obstacle, and then mark the skirting board accordingly. Use a mitre saw or a utility knife to make the necessary cuts, ensuring a precise fit around the obstacle.
Installing the Skirting Boards
With the skirting boards cut to size, it’s time to start the installation process.
Apply Adhesive
Using a caulking gun, apply a continuous bead of adhesive along the back of the skirting board. Make sure to apply the adhesive evenly, covering the entire length of the board. Pay special attention to the ends and corners of the board, as these areas will require extra adhesion.
Position the Skirting Board
Carefully place the skirting board against the wall, starting at one end of the wall. Press the board firmly against the wall, ensuring that it is level and straight. Use a spirit level to check the alignment of the board, and make any necessary adjustments. If the skirting board is not level, you can use shims to raise or lower the board until it is straight.
Secure the Skirting Board
Once the skirting board is in position, use a few nails or screws to temporarily secure it to the wall. This will help to hold the board in place while the adhesive dries. Make sure to drive the nails or screws into the wall studs or use wall plugs if there are no studs available. Space the nails or screws evenly along the length of the board, approximately every 30 – 40 cm.
Join the Skirting Boards
At corners, join the two mitre – cut skirting boards together. Apply a small amount of adhesive to the mitre joints, and then carefully press the boards together. Make sure the joints are tight and seamless. Use a clamp or a piece of scrap wood to hold the joints in place while the adhesive dries.
Seal the Gaps
After all the skirting boards are installed, use silicone sealant to fill the gaps between the skirting and the wall or floor. Apply the sealant along the edges of the skirting board, using a caulking gun. Smooth the sealant with a spatula or your finger to create a neat and professional finish.
Finishing Touches
Once the installation is complete and the adhesive and sealant have dried, you can add some finishing touches to your skirting.
Sand the Surface
If the skirting boards have any rough edges or surface imperfections, use sandpaper to smooth them out. Start with a coarse – grit sandpaper and then move to a finer – grit sandpaper for a smooth finish.
Paint the Skirting
PS skirting can be painted to match the color of your walls or to add a decorative touch. Choose a high – quality paint suitable for use on polystyrene surfaces. Apply the paint evenly using a brush or a roller, following the manufacturer’s instructions. You may need to apply multiple coats of paint for a uniform color.
Why Choose Our PS Skirting
As a supplier of PS skirting, we take pride in offering a wide range of high – quality products. Our PS skirting is made from premium polystyrene materials, which ensures durability and long – lasting performance. We offer a variety of styles and designs to suit different interior decoration needs, whether you prefer a modern, minimalist look or a more traditional, ornate style.
In addition to the quality of our products, we also provide excellent customer service. Our team is ready to assist you with any questions or concerns you may have during the installation process. We offer competitive pricing and can provide bulk discounts for larger orders.
PS Skirting If you’re interested in purchasing our PS skirting or have any questions about installation, we encourage you to contact us. We’d love to discuss your project and help you find the perfect skirting solution for your space. Whether you’re a DIY enthusiast or a professional contractor, our PS skirting is a great choice for enhancing the look of your home or commercial building.
References
- "Home Decorating Handbook" by an unknown author, a well – known interior design book.
- Manufacturer’s instructions for the PS skirting product.
- Professional installation guides from the DIY industry.
Linyi Xinchenda Import and Export Trading Co., Ltd.
We’re known as one of the most professional ps skirting manufacturers in China, also support customized service. With abundant experience, we warmly welcome you to buy premium ps skirting for sale here from our factory. Quality products and low price are available.
Address: NO. 20, ROOM 815, BUILDING 2, CENTURY PLAZA, BEIJING ROAD, LANSHAN DISTRICT, LINYI CITY, SHANDONG, CHINA
E-mail: lily311913@gmail.com
WebSite: https://www.xcdpswallpanel.com/
